Drill one hole at each end of the bracket with a 4.5mm drill, then screw the bracket onto the window frame using the 8g x 12 screws supplied making sure that the bracket does not interfere with the movement of the handle. Place a protection bracket over the top of an actuator and mark the position for holes to be drilled through the bracket. If the pins are not traveling in the same direction then reverse the connections to each actuator that is travelling in the opposite direction. Operate remote controller and make sure all actuator pins travel in the same direction at the same time and when the lock button is pressed all the pins are in the locked position. The EGR Premium canopies start with a sheet of ABS, the material is strong, thick and UV stable with acrylic capping to provide an excellent smooth surface as its first and final finish.Connect all actuators to cabling using female bullet connectors and then connect power to controller. Make sure the duct does not interfere with the movement of the pin of the actuators, however loom tube could be used instead of the plastic duct. Flexiglass are your canopy and tray specialists. We found it easiest to run cables in loom tube to inside the canopy and then run a piece of 25 x 16 duct under the window frame from front to rear on each side of the canopy holding it in place with double sided tape and some dobs of silicone. Referring to the wiring diagram, run a 15amp cable to the controller from a positive power source and connect the black wire to a negative, then run 2 wires (3mm 10amp) from the controller white & white/black to the first actuator and then loop wires to all other actuators. Mount controller anywhere in cabin (this is important for ease of accessibility in the event of unforeseen failure).Canopy replacement window flexiglass ute canopy arb canopy flexiglass.
Drill the two holes for pop rivets and mount small bracket using supplied pop rivets. Get the best deals on Sony PlayStation 5 Consoles and upgrade your gaming setup with a new gaming console 3 tonne under body. THE FRAMES ARE MADE OUT OF HEAVY DUTY ALUMINUM METAL AND THE TRIMMING COMES IN GOLD, CHROME, WHITE OR BLACK. PLEXIGLASS AWNINGS COME WITH EITHER CLEAR, TINTED, GOLD, OR GREEN POLYCARBONATED SHEETS. Then place and mark the position of the rear window bracket on the frame of the window making sure the lip of the bracket is facing towards the actuator, so if the window closes with the actuator in the locked position the bracket will push the pin into the actuator. Plexiglass - Zorox Awnings - Unbreakable Plastic. Hold an actuator on the rear window frame as near as possible to the window handle but not as to interfere with the movement of the handle, and making allowance if protection bracket is to be installed.Repeat step 1 & 2 for all 4 side window handles.The bracket can also be bent up or down to ensure the actuator pin engages with the pin when locked and clears the bracket when unlocked. This can be done by using a file to make the hole larger. Note: The hole in the bracket may have to be enlarged to ensure that the pin moves freely with the window handle in the open or closed position.Secure actuator to window frame using the 2 of the 8g x 12 screws. and comes loaded with features including a Flexiglass canopy, and 19-Inch alloys. Now push the pin of the actuator fully down to make sure that the top of the pin clears the bracket so the window can be opened. The UTE looks great but its out of my price for a second vehicle. Where the bracket is now installed place an actuator on the inside of the window frame under the bracket with the actuator pin extended upwards and line up the pin to the center of the hole in the bracket and the shoulder on the pin to the underside of the bracket.
Using the pop rivets supplied install the bracket onto the top of the window frame with the bent edge facing up. Drill two holes through the bracket and into the window frame with a 3.5mm pop rivet drill.
Select location for side window bracket (close to handle but leave enough room so as not to interfere with movement of handle, and making allowance if protection bracket is to be installed). Ute tray canvas canopy.Installation:(Note if you are unsure of these steps please refer to the picture gallery at - most steps are shown)